Examination Of Perlite-Polymer Interface Interactions in Polypropylene-Based Composites via Several Compatibilizers

Çağrıalp Arslan; Ümit Tayfun; Mehmet Doğan

Makale detayları

Examination Of Perlite-Polymer Interface Interactions in Polypropylene-Based Composites via Several Compatibilizers

Yazarlar:

Çağrıalp Arslan | Ümit Tayfun | Mehmet Doğan

Yayıncı:

Hitit University

Ana Başlıklar:

Composite and Hybrid Materials | Polymers and Plastics

Dergi:

Hittite Journal of Science and Engineering Vol.10 Issue 4, pp.323-329

Belge Tipi:

Makale

Yayın Tarihi:

12/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001309013

pISSN:

2148-4171

Anahtar kelimeler:

Özet:

 The surface interaction between the polymer and the mineral additive is one of the most significant aspects influencing the efficiency of mineral-filled polymeric composites. In this work, three distinct compatibilizers were introduced to composites based on polypropylene PP and perlite to improve interactions between the constituents. On composites comprising 10 expanded perlite content, three different ratios of ethylene vinyl acetate copolymer EVA, thermoplastic polyurethane elastomer TPU, and maleic anhydride grafted polypropylene MA-PP compatibilizers were employed. Composites were produced using an approach designated melt blending followed by injection molding. The composites containing MA-PP compatibilizer possessed the most outstanding performance, according to the results of mechanical, physical, and dynamic mechanical evaluations and morphological characterizations. The investigated aspects indicated a rise in the composites containing 10 percent compatibilizer with the lowest adding amount, whereas performances declined at high compatibilizer contents. Along with these results, it was determined that the compatibilizers included in the PPperlite composite system assisted in the fabrication of the composites by promoting the force values and melt flow rates identified during melt mixing. Following the test outcomes, MA-PP performed better than TPU and EVA in terms of compatibilizer efficiency. In general, it has been revealed that the selection of MA-PP compatibilizer in the manufacturing stages would offer benefits in terms of both simplicity of processing and mechanical strength where expanded perlite will be adopted as a natural filler for PP-based composites.

 The surface interaction between the polymer and the mineral additive is one of the most significant aspects influencing the efficiency of mineral-filled polymeric composites. In this work, three distinct compatibilizers were introduced to composites based on polypropylene PP and perlite to improve interactions between the constituents. On composites comprising 10 expanded perlite content, three different ratios of ethylene vinyl acetate copolymer EVA, thermoplastic polyurethane elastomer TPU, and maleic anhydride grafted polypropylene MA-PP compatibilizers were employed. Composites were produced using an approach designated melt blending followed by injection molding. The composites containing MA-PP compatibilizer possessed the most outstanding performance, according to the results of mechanical, physical, and dynamic mechanical evaluations and morphological characterizations. The investigated aspects indicated a rise in the composites containing 10 percent compatibilizer with the lowest adding amount, whereas performances declined at high compatibilizer contents. Along with these results, it was determined that the compatibilizers included in the PPperlite composite system assisted in the fabrication of the composites by promoting the force values and melt flow rates identified during melt mixing. Following the test outcomes, MA-PP performed better than TPU and EVA in terms of compatibilizer efficiency. In general, it has been revealed that the selection of MA-PP compatibilizer in the manufacturing stages would offer benefits in terms of both simplicity of processing and mechanical strength where expanded perlite will be adopted as a natural filler for PP-based composites.

 The surface interaction between the polymer and the mineral additive is one of the most significant aspects influencing the efficiency of mineral-filled polymeric composites. In this work, three distinct compatibilizers were introduced to composites based on polypropylene PP and perlite to improve interactions between the constituents. On composites comprising 10 expanded perlite content, three different ratios of ethylene vinyl acetate copolymer EVA, thermoplastic polyurethane elastomer TPU, and maleic anhydride grafted polypropylene MA-PP compatibilizers were employed. Composites were produced using an approach designated melt blending followed by injection molding. The composites containing MA-PP compatibilizer possessed the most outstanding performance, according to the results of mechanical, physical, and dynamic mechanical evaluations and morphological characterizations. The investigated aspects indicated a rise in the composites containing 10 percent compatibilizer with the lowest adding amount, whereas performances declined at high compatibilizer contents. Along with these results, it was determined that the compatibilizers included in the PPperlite composite system assisted in the fabrication of the composites by promoting the force values and melt flow rates identified during melt mixing. Following the test outcomes, MA-PP performed better than TPU and EVA in terms of compatibilizer efficiency. In general, it has been revealed that the selection of MA-PP compatibilizer in the manufacturing stages would offer benefits in terms of both simplicity of processing and mechanical strength where expanded perlite will be adopted as a natural filler for PP-based composites.

 The surface interaction between the polymer and the mineral additive is one of the most significant aspects influencing the efficiency of mineral-filled polymeric composites. In this work, three distinct compatibilizers were introduced to composites based on polypropylene PP and perlite to improve interactions between the constituents. On composites comprising 10 expanded perlite content, three different ratios of ethylene vinyl acetate copolymer EVA, thermoplastic polyurethane elastomer TPU, and maleic anhydride grafted polypropylene MA-PP compatibilizers were employed. Composites were produced using an approach designated melt blending followed by injection molding. The composites containing MA-PP compatibilizer possessed the most outstanding performance, according to the results of mechanical, physical, and dynamic mechanical evaluations and morphological characterizations. The investigated aspects indicated a rise in the composites containing 10 percent compatibilizer with the lowest adding amount, whereas performances declined at high compatibilizer contents. Along with these results, it was determined that the compatibilizers included in the PPperlite composite system assisted in the fabrication of the composites by promoting the force values and melt flow rates identified during melt mixing. Following the test outcomes, MA-PP performed better than TPU and EVA in terms of compatibilizer efficiency. In general, it has been revealed that the selection of MA-PP compatibilizer in the manufacturing stages would offer benefits in terms of both simplicity of processing and mechanical strength where expanded perlite will be adopted as a natural filler for PP-based composites.

Makale detayları

Examination Of Perlite-Polymer Interface Interactions in Polypropylene-Based Composites via Several Compatibilizers

Yazarlar:

Çağrıalp Arslan | Ümit Tayfun | Mehmet Doğan

Yayıncı:

Hitit University

Ana Başlıklar:

Composite and Hybrid Materials | Polymers and Plastics

Dergi:

Hittite Journal of Science and Engineering Vol.10 Issue 4, pp.323-329

Belge Tipi:

Makale

Yayın Tarihi:

12/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001309013

pISSN:

2148-4171

Mineral additive

Polymer composites

Expanded perlite

Compatibilizer

Polypropylene

Polymer processing

Sayı

Makale detayları

Examination Of Perlite-Polymer Interface Interactions in Polypropylene-Based Composites via Several Compatibilizers

Yazarlar: Çağrıalp Arslan | Ümit Tayfun | Mehmet Doğan

Yayıncı: Hitit University

Ana Başlıklar: Composite and Hybrid Materials | Polymers and Plastics

Dergi: Hittite Journal of Science and Engineering Vol.10 Issue 4, pp.323-329

Belge Tipi: Makale

Yayın Tarihi: 12/2023

Belge Dili: İngilizce

Document ID (Org No.): 2001309013

pISSN: 2148-4171

Mineral additive

Polymer composites

Expanded perlite

Compatibilizer

Polypropylene

Polymer processing

Sayı

Yazarlar:

Çağrıalp Arslan | Ümit Tayfun | Mehmet Doğan

Yayıncı:

Hitit University

Ana Başlıklar:

Composite and Hybrid Materials | Polymers and Plastics

Dergi:

Hittite Journal of Science and Engineering Vol.10 Issue 4, pp.323-329

Belge Tipi:

Makale

Yayın Tarihi:

12/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001309013

pISSN:

2148-4171