WEAR PROPERTIES OF AL-CU-MG COMPOSITES REINFORCED WITH MGO AND MWCNT UNDER DIFFERENT LOADS

Engin ERGÜL; Halil İbrahim KURT; Murat ODUNCUOĞLU; Can ÇİVİ

Makale detayları

WEAR PROPERTIES OF AL-CU-MG COMPOSITES REINFORCED WITH MGO AND MWCNT UNDER DIFFERENT LOADS

Yazarlar:

Engin ERGÜL | Halil İbrahim KURT | Murat ODUNCUOĞLU | Can ÇİVİ

Yayıncı:

Necip Fazıl YILMAZ

Ana Başlıklar:

İmalat

Dergi:

The International Journal of Materials and Engineering Technology 2019 Vol.2 Issue 2, pp.70-75

Belge Tipi:

Makale

Yayın Tarihi:

12/2019

Belge Dili:

İngilizce

Document ID (Org No.):

2000664151

Sıklık:

İki Yıllık

eISSN:

2667-4033

Özet:

 

Wear of metals is one of the most important mechanisms encountered on engineering basis. Especially in places where there is friction, it is important to use engineering materials with high friction resistance. In this study, 40 nm diameter nano magnesium oxide and 1.5 micron long and 9.5 nm diameter multiple walled carbon nano tubes were added to Al-Cu-Mg alloy. 50 wt% MGO and 50 wt% MWCNT were mixed and added to the matrix material in 1wt% and the composite materials were produced by the semi-solid mixing method. The aim of this study was to investigate the major tribological factors affecting the abrasive wear behavior of Al-Cu-Mg composites reinforced with MGO/MWCNT. Composite materials were produced by semi-solid mixing method. The wear behavior of MGO/MWCNT reinforced Al-Cu-Mg alloy aluminum matrix composites (Al MMCs) was investigated. Wear properties were investigated under different loads and the shear rate and shear distance were kept constant. Abrasion tests were carried out considering the weight loss at 500 m distance under 2N and 5N load on the ball-on-disc type wear device. Al-Cu-Mg wear weight loss was reduced by approximately 49% with the addition of 50% CNT 50% MgO 1% wt.

Makale detayları

WEAR PROPERTIES OF AL-CU-MG COMPOSITES REINFORCED WITH MGO AND MWCNT UNDER DIFFERENT LOADS

Yazarlar: Engin ERGÜL | Halil İbrahim KURT | Murat ODUNCUOĞLU | Can ÇİVİ

Yayıncı: Necip Fazıl YILMAZ

Ana Başlıklar: İmalat

Dergi: The International Journal of Materials and Engineering Technology 2019 Vol.2 Issue 2, pp.70-75

Belge Tipi: Makale

Yayın Tarihi: 12/2019

Belge Dili: İngilizce

Document ID (Org No.): 2000664151

Sıklık: İki Yıllık

eISSN: 2667-4033

Sayı

Yazarlar:

Engin ERGÜL | Halil İbrahim KURT | Murat ODUNCUOĞLU | Can ÇİVİ

Yayıncı:

Necip Fazıl YILMAZ

Ana Başlıklar:

İmalat

Dergi:

The International Journal of Materials and Engineering Technology 2019 Vol.2 Issue 2, pp.70-75

Belge Tipi:

Makale

Yayın Tarihi:

12/2019

Belge Dili:

İngilizce

Document ID (Org No.):

2000664151

Sıklık:

İki Yıllık

eISSN:

2667-4033