Numerical Modeling of Mechanical Strength of Tİ6AL4V Gyroid Structures for Orthopedic Implants

Fatma Nur Depboylu; Özgür Poyraz; Evren Yasa; Feza Korkusuz

Makale detayları

Numerical Modeling of Mechanical Strength of Tİ6AL4V Gyroid Structures for Orthopedic Implants

Yazarlar:

Fatma Nur Depboylu | Özgür Poyraz | Evren Yasa | Feza Korkusuz

Yayıncı:

Afyon Kocatepe University

Ana Başlıklar:

Biyomateryaller | Biyomedikal Mühendisliği

Dergi:

Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi Vol.23 Issue 1, pp.270-283

Belge Tipi:

Makale

Yayın Tarihi:

1/2023

Belge Dili:

Türkçe

Document ID (Org No.):

2001284433

pISSN:

2149-3367

Anahtar kelimeler:

Özet:

 Metal orthopedic implants are widely used to maintain stability during tissue repair in joint and bone injuries to restore function. Elastic modulus values suitable for the area where the implants carry the load-bearing part and have biocompatibility features that prevent harmful effects on the body are the minimum requirements. Widespread studies on the ideal implant material are on titanium and titanium alloy implants due to their high mechanical strength and osteointegration properties. However, in cases where it is desired to remain in the body after implantation, porous implants with triply periodic minimal surface TPMS lattice structures are used in order to increase the bioactivity further and reach the mechanical properties of the bone. In the study, Ti6Al4V with gyroid pore structure, one of the controlled TPMS lattice structures planned to be produced by laser powder bed fusion technology, was designed with different porosity rates between 40-80. Then, the focus is on examining the mechanical strength and deformation behaviors under compression for each design with the finite element analysis. The results of the study were compared with the compression test of gyroid Ti6Al4V structures produced by laser powder bed fusion from the literature and consistent results were obtained.

 Metal orthopedic implants are widely used to maintain stability during tissue repair in joint and bone injuries to restore function. Elastic modulus values suitable for the area where the implants carry the load-bearing part and have biocompatibility features that prevent harmful effects on the body are the minimum requirements. Widespread studies on the ideal implant material are on titanium and titanium alloy implants due to their high mechanical strength and osteointegration properties. However, in cases where it is desired to remain in the body after implantation, porous implants with triply periodic minimal surface TPMS lattice structures are used in order to increase the bioactivity further and reach the mechanical properties of the bone. In the study, Ti6Al4V with gyroid pore structure, one of the controlled TPMS lattice structures planned to be produced by laser powder bed fusion technology, was designed with different porosity rates between 40-80. Then, the focus is on examining the mechanical strength and deformation behaviors under compression for each design with the finite element analysis. The results of the study were compared with the compression test of gyroid Ti6Al4V structures produced by laser powder bed fusion from the literature and consistent results were obtained.

 Metal orthopedic implants are widely used to maintain stability during tissue repair in joint and bone injuries to restore function. Elastic modulus values suitable for the area where the implants carry the load-bearing part and have biocompatibility features that prevent harmful effects on the body are the minimum requirements. Widespread studies on the ideal implant material are on titanium and titanium alloy implants due to their high mechanical strength and osteointegration properties. However, in cases where it is desired to remain in the body after implantation, porous implants with triply periodic minimal surface TPMS lattice structures are used in order to increase the bioactivity further and reach the mechanical properties of the bone. In the study, Ti6Al4V with gyroid pore structure, one of the controlled TPMS lattice structures planned to be produced by laser powder bed fusion technology, was designed with different porosity rates between 40-80. Then, the focus is on examining the mechanical strength and deformation behaviors under compression for each design with the finite element analysis. The results of the study were compared with the compression test of gyroid Ti6Al4V structures produced by laser powder bed fusion from the literature and consistent results were obtained.

 Ortopedik metal implantlar fonksiyonun geri kazanılması amacıyla eklem ve kemik dokusunun onarımı sürecinde sağlamlığı korumak için yaygın kullanılır. İmplantların yük taşıma işlevi gören bölgeye uygun elastik modül değeri ve vücutta oluşacak olumsuz etkileri önleyici biyouyumluluk özelliklerinin olması, minimum gereksinimlerdir. İdeal implant malzemesi üzerine yaygınlaşmış çalışmalar, yüksek mekanik dayanıklılık ve osteointegrasyon özellikleri nedeniyle titanyum ve titanyum alaşımlı implantlar üzerinedir. Ancak implantasyon sonrası vücutta kalması istenen durumlarda biyoaktiviteyi daha da artırmak ve kemiğin mekanik özelliklerine yaklaşmak amacıyla üçlü periyodik minimal yüzey ÜPMY kafes yapısına sahip gözenekli implantlar kullanılır. Çalışma, istenen mekanik özellikleri ve gözenekler arası hücre hareketini sağlamak için kontrollü ÜPMY kafes yapılarından gyroid gözenek yapısına sahip lazer toz yatağında füzyon ile üretimi planlanan Ti6Al4V ilk olarak 40-80 arasında farklı gözeneklilik oranlarında tasarlanmıştır. Ardından her bir tasarım için basma altında mekanik dayanım ve deformasyon davranışlarını sonlu eleman analizi altında incelemeye odaklanılmıştır. Literatüre bakıldığında lazer toz yatağında füzyon ile üretilen gyroid Ti6Al4V yapıların basma testi sonuçları ile karşılaştırılmış ve uyumlu sonuçlar alınmıştır.

Makale detayları

Numerical Modeling of Mechanical Strength of Tİ6AL4V Gyroid Structures for Orthopedic Implants

Yazarlar:

Fatma Nur Depboylu | Özgür Poyraz | Evren Yasa | Feza Korkusuz

Yayıncı:

Afyon Kocatepe University

Ana Başlıklar:

Biyomateryaller | Biyomedikal Mühendisliği

Dergi:

Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi Vol.23 Issue 1, pp.270-283

Belge Tipi:

Makale

Yayın Tarihi:

1/2023

Belge Dili:

Türkçe

Document ID (Org No.):

2001284433

pISSN:

2149-3367

Finite Element Analysis

Gyroid Lattice Structure Design

Orthopedic Implant

Titanium

Triply Periodic Minimal Surfaces

Sonlu Elemanlar Analizi

Ortopedik İmplant

Titanyum

Üçlü Periyodik Minimal Yüzeyler

Gyroid Kafes Yapı Tasarımı

Sayı

Makale detayları

Yazarlar: Fatma Nur Depboylu | Özgür Poyraz | Evren Yasa | Feza Korkusuz

Yayıncı: Afyon Kocatepe University

Ana Başlıklar: Biyomateryaller | Biyomedikal Mühendisliği

Dergi: Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi Vol.23 Issue 1, pp.270-283

Belge Tipi: Makale

Yayın Tarihi: 1/2023

Belge Dili: Türkçe

Document ID (Org No.): 2001284433

pISSN: 2149-3367

Sayı

Yazarlar:

Fatma Nur Depboylu | Özgür Poyraz | Evren Yasa | Feza Korkusuz

Yayıncı:

Afyon Kocatepe University

Ana Başlıklar:

Biyomateryaller | Biyomedikal Mühendisliği

Dergi:

Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi Vol.23 Issue 1, pp.270-283

Belge Tipi:

Makale

Yayın Tarihi:

1/2023

Belge Dili:

Türkçe

Document ID (Org No.):

2001284433

pISSN:

2149-3367