Investigation and Optimization of The Effect of Anhydrous Borax Mineral on The Vickers Hardness and Indentation Modulus Values of Iron Material

Şenol Şahin; Ayşegül Bodur Yılmaz; Talha Tunahan Kesemenli

Makale detayları

Investigation and Optimization of The Effect of Anhydrous Borax Mineral on The Vickers Hardness and Indentation Modulus Values of Iron Material

Yazarlar:

Şenol Şahin | Ayşegül Bodur Yılmaz | Talha Tunahan Kesemenli

Yayıncı:

Kyrgyz-Turkish Manas University

Ana Başlıklar:

Engineering

Dergi:

MANAS Journal of Engineering Vol.12 Issue 1, pp.39-45

Belge Tipi:

Makale

Yayın Tarihi:

6/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001319844

pISSN:

1694-7398

Anahtar kelimeler:

Özet:

 In this study, 5 and 10 by weight of anhydrous borax AHB was added to the iron Fe matrix material by powder metallurgy method and the effects of the additive ratio on the Vickers hardness HV, Brinell hardness HB and Indentation modulus EIT values of the composites FeAHB were investigated. In the productions carried out using Taguchi experimental design method, AHB additive ratio, and sintering temperature parameters were selected as control parameters that were thought to affect the physical andor mechanical properties of the FeAHB composite materials. The productions were carried out according to the Taguchi L4 orthogonal array, which was created depending on the control parameters and levels. Vickers hardness and indentation modulus measurements of pure iron and FeAHB composite materials were performed in accordance with BS EN ISO 14577-1 standard and Brinell hardness measurement was performed in accordance with TS EN ISO 6506-1 standard. According to the signal-to-noise ratio SN analysis performed with the experimental data, it was determined that the 10 AHB additive ratio and 950oC sintering temperature optimized all the investigated properties of the FeAHB composite material. It was determined that the values for Vickers hardness, Brinell hardness and indentation modulus increased by 142.03, 69.32 and 144.11, respectively, in the levels where the properties of the composite material were optimized compared to pure Fe material. As a result of the qualitative examination of all samples after storage in a comfortable environment without daylight, it was also observed that the anhydrous borax additive delayed the corrosion time of pure iron material.

 In this study, 5 and 10 by weight of anhydrous borax AHB was added to the iron Fe matrix material by powder metallurgy method and the effects of the additive ratio on the Vickers hardness HV, Brinell hardness HB and Indentation modulus EIT values of the composites FeAHB were investigated. In the productions carried out using Taguchi experimental design method, AHB additive ratio, and sintering temperature parameters were selected as control parameters that were thought to affect the physical andor mechanical properties of the FeAHB composite materials. The productions were carried out according to the Taguchi L4 orthogonal array, which was created depending on the control parameters and levels. Vickers hardness and indentation modulus measurements of pure iron and FeAHB composite materials were performed in accordance with BS EN ISO 14577-1 standard and Brinell hardness measurement was performed in accordance with TS EN ISO 6506-1 standard. According to the signal-to-noise ratio SN analysis performed with the experimental data, it was determined that the 10 AHB additive ratio and 950oC sintering temperature optimized all the investigated properties of the FeAHB composite material. It was determined that the values for Vickers hardness, Brinell hardness and indentation modulus increased by 142.03, 69.32 and 144.11, respectively, in the levels where the properties of the composite material were optimized compared to pure Fe material. As a result of the qualitative examination of all samples after storage in a comfortable environment without daylight, it was also observed that the anhydrous borax additive delayed the corrosion time of pure iron material.

 In this study, 5 and 10 by weight of anhydrous borax AHB was added to the iron Fe matrix material by powder metallurgy method and the effects of the additive ratio on the Vickers hardness HV, Brinell hardness HB and Indentation modulus EIT values of the composites FeAHB were investigated. In the productions carried out using Taguchi experimental design method, AHB additive ratio, and sintering temperature parameters were selected as control parameters that were thought to affect the physical andor mechanical properties of the FeAHB composite materials. The productions were carried out according to the Taguchi L4 orthogonal array, which was created depending on the control parameters and levels. Vickers hardness and indentation modulus measurements of pure iron and FeAHB composite materials were performed in accordance with BS EN ISO 14577-1 standard and Brinell hardness measurement was performed in accordance with TS EN ISO 6506-1 standard. According to the signal-to-noise ratio SN analysis performed with the experimental data, it was determined that the 10 AHB additive ratio and 950oC sintering temperature optimized all the investigated properties of the FeAHB composite material. It was determined that the values for Vickers hardness, Brinell hardness and indentation modulus increased by 142.03, 69.32 and 144.11, respectively, in the levels where the properties of the composite material were optimized compared to pure Fe material. As a result of the qualitative examination of all samples after storage in a comfortable environment without daylight, it was also observed that the anhydrous borax additive delayed the corrosion time of pure iron material.

 In this study, 5 and 10 by weight of anhydrous borax AHB was added to the iron Fe matrix material by powder metallurgy method and the effects of the additive ratio on the Vickers hardness HV, Brinell hardness HB and Indentation modulus EIT values of the composites FeAHB were investigated. In the productions carried out using Taguchi experimental design method, AHB additive ratio, and sintering temperature parameters were selected as control parameters that were thought to affect the physical andor mechanical properties of the FeAHB composite materials. The productions were carried out according to the Taguchi L4 orthogonal array, which was created depending on the control parameters and levels. Vickers hardness and indentation modulus measurements of pure iron and FeAHB composite materials were performed in accordance with BS EN ISO 14577-1 standard and Brinell hardness measurement was performed in accordance with TS EN ISO 6506-1 standard. According to the signal-to-noise ratio SN analysis performed with the experimental data, it was determined that the 10 AHB additive ratio and 950oC sintering temperature optimized all the investigated properties of the FeAHB composite material. It was determined that the values for Vickers hardness, Brinell hardness and indentation modulus increased by 142.03, 69.32 and 144.11, respectively, in the levels where the properties of the composite material were optimized compared to pure Fe material. As a result of the qualitative examination of all samples after storage in a comfortable environment without daylight, it was also observed that the anhydrous borax additive delayed the corrosion time of pure iron material.

Makale detayları

Investigation and Optimization of The Effect of Anhydrous Borax Mineral on The Vickers Hardness and Indentation Modulus Values of Iron Material

Yazarlar:

Şenol Şahin | Ayşegül Bodur Yılmaz | Talha Tunahan Kesemenli

Yayıncı:

Kyrgyz-Turkish Manas University

Ana Başlıklar:

Engineering

Dergi:

MANAS Journal of Engineering Vol.12 Issue 1, pp.39-45

Belge Tipi:

Makale

Yayın Tarihi:

6/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001319844

pISSN:

1694-7398

Anhydrous borax

composites

hardness

iron

powder metallurgyAnhydrous borax

composites

hardness

iron

powder metallurgy

Sayı

Makale detayları

Yazarlar: Şenol Şahin | Ayşegül Bodur Yılmaz | Talha Tunahan Kesemenli

Yayıncı: Kyrgyz-Turkish Manas University

Ana Başlıklar: Engineering

Dergi: MANAS Journal of Engineering Vol.12 Issue 1, pp.39-45

Belge Tipi: Makale

Yayın Tarihi: 6/2024

Belge Dili: İngilizce

Document ID (Org No.): 2001319844

pISSN: 1694-7398

Sayı

Yazarlar:

Şenol Şahin | Ayşegül Bodur Yılmaz | Talha Tunahan Kesemenli

Yayıncı:

Kyrgyz-Turkish Manas University

Ana Başlıklar:

Engineering

Dergi:

MANAS Journal of Engineering Vol.12 Issue 1, pp.39-45

Belge Tipi:

Makale

Yayın Tarihi:

6/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001319844

pISSN:

1694-7398