Effects of SiO2 and Al2O3 nanoparticles on the properties of borogypsum containing mortar

Meral Yıldırım Özen; Emek Moroydor Derun

Makale detayları

Effects of SiO2 and Al2O3 nanoparticles on the properties of borogypsum containing mortar

Yazarlar:

Meral Yıldırım Özen | Emek Moroydor Derun

Yayıncı:

Yildiz Technical University

Ana Başlıklar:

Clinical Sciences (Other)

Dergi:

Sigma Journal of Engineering and Natural Sciences Vol.42 Issue 6, pp.1923-1932

Belge Tipi:

Makale

Yayın Tarihi:

9/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001333127

pISSN:

1304-7191

Anahtar kelimeler:

Özet:

 This study aimed to investigate the effects of nano-SiO2 and nano-Al2O3 on the physicochem-ical and mechanical properties of mortars containing borogypsum. The mortars were modi fied by incorporating 0.2-1 nano-SiO2 and 0.5-2.5 nano-Al2O3. Various analysis methods were applied to the nano-modified samples to observe changes in the fresh and hardened features of the mortars. The results showed that the nanoparticles used could not promote the setting of the mortars. The highest compressive strength of 67 MPa was achieved when 1 nano-Al2O3 was used. Adding 0.4 nano-SiO2 resulted in the highest flexural strength of 9.13 MPa. Supporting the water absorption test, SEM and BET morphologic analyses showed that nano-SiO2 was more effective in developing a denser microstructure than nano-Al2O3. The findings of the thermal analysis suggest that substituting nanoparticles in borogypsum-containing mortars could not decrease the unreacted CH ratio during the hydration under the studied conditions.

 This study aimed to investigate the effects of nano-SiO2 and nano-Al2O3 on the physicochem-ical and mechanical properties of mortars containing borogypsum. The mortars were modi fied by incorporating 0.2-1 nano-SiO2 and 0.5-2.5 nano-Al2O3. Various analysis methods were applied to the nano-modified samples to observe changes in the fresh and hardened features of the mortars. The results showed that the nanoparticles used could not promote the setting of the mortars. The highest compressive strength of 67 MPa was achieved when 1 nano-Al2O3 was used. Adding 0.4 nano-SiO2 resulted in the highest flexural strength of 9.13 MPa. Supporting the water absorption test, SEM and BET morphologic analyses showed that nano-SiO2 was more effective in developing a denser microstructure than nano-Al2O3. The findings of the thermal analysis suggest that substituting nanoparticles in borogypsum-containing mortars could not decrease the unreacted CH ratio during the hydration under the studied conditions.

 This study aimed to investigate the effects of nano-SiO2 and nano-Al2O3 on the physicochem-ical and mechanical properties of mortars containing borogypsum. The mortars were modi fied by incorporating 0.2-1 nano-SiO2 and 0.5-2.5 nano-Al2O3. Various analysis methods were applied to the nano-modified samples to observe changes in the fresh and hardened features of the mortars. The results showed that the nanoparticles used could not promote the setting of the mortars. The highest compressive strength of 67 MPa was achieved when 1 nano-Al2O3 was used. Adding 0.4 nano-SiO2 resulted in the highest flexural strength of 9.13 MPa. Supporting the water absorption test, SEM and BET morphologic analyses showed that nano-SiO2 was more effective in developing a denser microstructure than nano-Al2O3. The findings of the thermal analysis suggest that substituting nanoparticles in borogypsum-containing mortars could not decrease the unreacted CH ratio during the hydration under the studied conditions.

 This study aimed to investigate the effects of nano-SiO2 and nano-Al2O3 on the physicochem-ical and mechanical properties of mortars containing borogypsum. The mortars were modi fied by incorporating 0.2-1 nano-SiO2 and 0.5-2.5 nano-Al2O3. Various analysis methods were applied to the nano-modified samples to observe changes in the fresh and hardened features of the mortars. The results showed that the nanoparticles used could not promote the setting of the mortars. The highest compressive strength of 67 MPa was achieved when 1 nano-Al2O3 was used. Adding 0.4 nano-SiO2 resulted in the highest flexural strength of 9.13 MPa. Supporting the water absorption test, SEM and BET morphologic analyses showed that nano-SiO2 was more effective in developing a denser microstructure than nano-Al2O3. The findings of the thermal analysis suggest that substituting nanoparticles in borogypsum-containing mortars could not decrease the unreacted CH ratio during the hydration under the studied conditions.

Makale detayları

Effects of SiO2 and Al2O3 nanoparticles on the properties of borogypsum containing mortar

Yazarlar:

Meral Yıldırım Özen | Emek Moroydor Derun

Yayıncı:

Yildiz Technical University

Ana Başlıklar:

Clinical Sciences (Other)

Dergi:

Sigma Journal of Engineering and Natural Sciences Vol.42 Issue 6, pp.1923-1932

Belge Tipi:

Makale

Yayın Tarihi:

9/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001333127

pISSN:

1304-7191

Borogypsum

Cement Mortar

Nanoparticle

Nano-SiO2

Nano- Al2O3

Sayı

Makale detayları

Effects of SiO2 and Al2O3 nanoparticles on the properties of borogypsum containing mortar

Yazarlar: Meral Yıldırım Özen | Emek Moroydor Derun

Yayıncı: Yildiz Technical University

Ana Başlıklar: Clinical Sciences (Other)

Dergi: Sigma Journal of Engineering and Natural Sciences Vol.42 Issue 6, pp.1923-1932

Belge Tipi: Makale

Yayın Tarihi: 9/2024

Belge Dili: İngilizce

Document ID (Org No.): 2001333127

pISSN: 1304-7191

Borogypsum

Cement Mortar

Nanoparticle

Nano-SiO2

Nano- Al2O3

Sayı

Yazarlar:

Meral Yıldırım Özen | Emek Moroydor Derun

Yayıncı:

Yildiz Technical University

Ana Başlıklar:

Clinical Sciences (Other)

Dergi:

Sigma Journal of Engineering and Natural Sciences Vol.42 Issue 6, pp.1923-1932

Belge Tipi:

Makale

Yayın Tarihi:

9/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001333127

pISSN:

1304-7191