Optimization of the Effect of Welding Parameters on Joint Strength in Butt Welding of Hdpe Pipes by Surface Response Method

Muhammet Dağlı; Ahmet Demirer; Esra Yumat

Makale detayları

Optimization of the Effect of Welding Parameters on Joint Strength in Butt Welding of Hdpe Pipes by Surface Response Method

Yazarlar:

Muhammet Dağlı | Ahmet Demirer | Esra Yumat

Yayıncı:

Afyon Kocatepe University

Ana Başlıklar:

Mühendislik | Malzeme Karekterizasyonu

Dergi:

Afyon Kocatepe Üniversitesi Uluslararası Mühendislik Teknolojileri ve Uygulamalı Bilimler Dergisi Vol.6 Issue 2, pp.95-109

Belge Tipi:

Makale

Yayın Tarihi:

12/2023

Belge Dili:

Türkçe

Document ID (Org No.):

2001304111

pISSN:

2667-4165

Anahtar kelimeler:

Özet:

 In the study, butt welding process of PE100 material, which is of HDPE material class and is used extensively in underground water and gas transportation, has been carried out experimentally. In the study, welded joints were performed using three different welding temperatures, three different joint pressures and three different heating times. The data obtained were evaluated and handled in the statistical data analysis program Design Expert 12. In the study, our variable selection and parameters are different, and optimization was carried out with the  Response Surface Methodology RSM. The samples produced with the optimum parameters obtained were subjected to both tensile test and hydrostatic strength tests and the results were evaluated. As a result of butt welding, optimum parameters 223oC, 15 bar, 120 sec were determined and the maximum tensile strength value was determined to be 19.50 MPa.

 In the study, butt welding process of PE100 material, which is of HDPE material class and is used extensively in underground water and gas transportation, has been carried out experimentally. In the study, welded joints were performed using three different welding temperatures, three different joint pressures and three different heating times. The data obtained were evaluated and handled in the statistical data analysis program Design Expert 12. In the study, our variable selection and parameters are different, and optimization was carried out with the  Response Surface Methodology RSM. The samples produced with the optimum parameters obtained were subjected to both tensile test and hydrostatic strength tests and the results were evaluated. As a result of butt welding, optimum parameters 223oC, 15 bar, 120 sec were determined and the maximum tensile strength value was determined to be 19.50 MPa.

 In the study, butt welding process of PE100 material, which is of HDPE material class and is used extensively in underground water and gas transportation, has been carried out experimentally. In the study, welded joints were performed using three different welding temperatures, three different joint pressures and three different heating times. The data obtained were evaluated and handled in the statistical data analysis program Design Expert 12. In the study, our variable selection and parameters are different, and optimization was carried out with the  Response Surface Methodology RSM. The samples produced with the optimum parameters obtained were subjected to both tensile test and hydrostatic strength tests and the results were evaluated. As a result of butt welding, optimum parameters 223oC, 15 bar, 120 sec were determined and the maximum tensile strength value was determined to be 19.50 MPa.

 Yapılan çalışmada HDPE malzeme sınıfından olan ve yeraltı su ve gaz naklinde yoğun olarak kullanılan PE100 malzemenin deneysel olarak alın kaynak işlemi gerçekleştirilmiştir. Çalışmada üç farklı kaynak sıcaklığı, üç farklı birleştirme basıncında ve üç faklı ısıtma süresi kullanılarak kaynaklı bağlantı gerçekleştirilmiştir. Elde edilen veriler istatistiksel veri analiz programında Design Expert 12 değerlendirilerek ele alınmıştır. Çalışmada değişken seçimimiz ve parametrelerimiz farklı olup Yüzey cevap metodu RSM ile optimizasyonu gerçekleştirilmiştir. Elde edilen optimum parametreler ile üretilmiş olan numuneler hem çekme testi hem de hidrostatik mukavemet testlerine tabi tutularak sonuçlar değerlendirilmiştir. Alın kaynağı sonucunda optimum parametreler 223oC, 15 bar, 120 sn belirlenmiş ve maksimum çekme dayanımı değerinin, 19,50 MPa olduğu tespit edilmiştir.

Makale detayları

Optimization of the Effect of Welding Parameters on Joint Strength in Butt Welding of Hdpe Pipes by Surface Response Method

Yazarlar:

Muhammet Dağlı | Ahmet Demirer | Esra Yumat

Yayıncı:

Afyon Kocatepe University

Ana Başlıklar:

Mühendislik | Malzeme Karekterizasyonu

Dergi:

Afyon Kocatepe Üniversitesi Uluslararası Mühendislik Teknolojileri ve Uygulamalı Bilimler Dergisi Vol.6 Issue 2, pp.95-109

Belge Tipi:

Makale

Yayın Tarihi:

12/2023

Belge Dili:

Türkçe

Document ID (Org No.):

2001304111

pISSN:

2667-4165

Butt Welding

PE100

Response Surface Method (RSMAlın kaynak

PE100

Yüzey Cevap Metodu

Sayı

Makale detayları

Optimization of the Effect of Welding Parameters on Joint Strength in Butt Welding of Hdpe Pipes by Surface Response Method

Yazarlar: Muhammet Dağlı | Ahmet Demirer | Esra Yumat

Yayıncı: Afyon Kocatepe University

Ana Başlıklar: Mühendislik | Malzeme Karekterizasyonu

Dergi: Afyon Kocatepe Üniversitesi Uluslararası Mühendislik Teknolojileri ve Uygulamalı Bilimler Dergisi Vol.6 Issue 2, pp.95-109

Belge Tipi: Makale

Yayın Tarihi: 12/2023

Belge Dili: Türkçe

Document ID (Org No.): 2001304111

pISSN: 2667-4165

Butt Welding

PE100

Response Surface Method (RSMAlın kaynak

PE100

Yüzey Cevap Metodu

Sayı

Yazarlar:

Muhammet Dağlı | Ahmet Demirer | Esra Yumat

Yayıncı:

Afyon Kocatepe University

Ana Başlıklar:

Mühendislik | Malzeme Karekterizasyonu

Dergi:

Afyon Kocatepe Üniversitesi Uluslararası Mühendislik Teknolojileri ve Uygulamalı Bilimler Dergisi Vol.6 Issue 2, pp.95-109

Belge Tipi:

Makale

Yayın Tarihi:

12/2023

Belge Dili:

Türkçe

Document ID (Org No.):

2001304111

pISSN:

2667-4165