An Ivestigation on Abrasion Resistance And Bending Rigidity of Recycled Nonwovens Including Blanket Trimmings

Gonca Alan; Mevlüt Tercan

Makale detayları

An Ivestigation on Abrasion Resistance And Bending Rigidity of Recycled Nonwovens Including Blanket Trimmings

Yazarlar:

Gonca Alan | Mevlüt Tercan

Yayıncı:

Ege University

Ana Başlıklar:

Wearable Materials

Dergi:

Textile and Apparel Vol.33 Issue 2, pp.176-184

Belge Tipi:

Makale

Yayın Tarihi:

6/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001293050

pISSN:

1300-3356

Anahtar kelimeler:

Özet:

 In this study blanket trimmings and mechanically recycled fibers were blended and softly pre-needlepunched to be used as innerlayers of conventional needle-punched nonwovens. The outer layers from three types of raw materials polypropylene, recycled polyester and mechanically recycled fibers and the control groups were produced by classical needle-punching at two different needle-punch densities. Abrasion resistance and bending properties of the end products were investigated considering recycled layer ratio, raw material type and needle-punching density through standard test methods. Among all types, the highest abrasion cycles and bending rigidity values were observed for the PP outer layered products. Increase in needling density increased the abrasion cycles between 10-20 and increased bending rigidity 3-8 among the overall. Comparing the fabrics with recycled layer of 20 to control groups, abrasion resistance was preserved between 67 -75 and bending rigidity was preserved between 86-93 at overall.

 In this study blanket trimmings and mechanically recycled fibers were blended and softly pre-needlepunched to be used as innerlayers of conventional needle-punched nonwovens. The outer layers from three types of raw materials polypropylene, recycled polyester and mechanically recycled fibers and the control groups were produced by classical needle-punching at two different needle-punch densities. Abrasion resistance and bending properties of the end products were investigated considering recycled layer ratio, raw material type and needle-punching density through standard test methods. Among all types, the highest abrasion cycles and bending rigidity values were observed for the PP outer layered products. Increase in needling density increased the abrasion cycles between 10-20 and increased bending rigidity 3-8 among the overall. Comparing the fabrics with recycled layer of 20 to control groups, abrasion resistance was preserved between 67 -75 and bending rigidity was preserved between 86-93 at overall.

 In this study blanket trimmings and mechanically recycled fibers were blended and softly pre-needlepunched to be used as innerlayers of conventional needle-punched nonwovens. The outer layers from three types of raw materials polypropylene, recycled polyester and mechanically recycled fibers and the control groups were produced by classical needle-punching at two different needle-punch densities. Abrasion resistance and bending properties of the end products were investigated considering recycled layer ratio, raw material type and needle-punching density through standard test methods. Among all types, the highest abrasion cycles and bending rigidity values were observed for the PP outer layered products. Increase in needling density increased the abrasion cycles between 10-20 and increased bending rigidity 3-8 among the overall. Comparing the fabrics with recycled layer of 20 to control groups, abrasion resistance was preserved between 67 -75 and bending rigidity was preserved between 86-93 at overall.

 In this study blanket trimmings and mechanically recycled fibers were blended and softly pre-needlepunched to be used as innerlayers of conventional needle-punched nonwovens. The outer layers from three types of raw materials polypropylene, recycled polyester and mechanically recycled fibers and the control groups were produced by classical needle-punching at two different needle-punch densities. Abrasion resistance and bending properties of the end products were investigated considering recycled layer ratio, raw material type and needle-punching density through standard test methods. Among all types, the highest abrasion cycles and bending rigidity values were observed for the PP outer layered products. Increase in needling density increased the abrasion cycles between 10-20 and increased bending rigidity 3-8 among the overall. Comparing the fabrics with recycled layer of 20 to control groups, abrasion resistance was preserved between 67 -75 and bending rigidity was preserved between 86-93 at overall.

Makale detayları

An Ivestigation on Abrasion Resistance And Bending Rigidity of Recycled Nonwovens Including Blanket Trimmings

Yazarlar:

Gonca Alan | Mevlüt Tercan

Yayıncı:

Ege University

Ana Başlıklar:

Wearable Materials

Dergi:

Textile and Apparel Vol.33 Issue 2, pp.176-184

Belge Tipi:

Makale

Yayın Tarihi:

6/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001293050

pISSN:

1300-3356

Recycling

needlepunched nonwovens

abrasion resistance

bending rigidity

Sayı

Makale detayları

An Ivestigation on Abrasion Resistance And Bending Rigidity of Recycled Nonwovens Including Blanket Trimmings

Yazarlar: Gonca Alan | Mevlüt Tercan

Yayıncı: Ege University

Ana Başlıklar: Wearable Materials

Dergi: Textile and Apparel Vol.33 Issue 2, pp.176-184

Belge Tipi: Makale

Yayın Tarihi: 6/2023

Belge Dili: İngilizce

Document ID (Org No.): 2001293050

pISSN: 1300-3356

Recycling

needlepunched nonwovens

abrasion resistance

bending rigidity

Sayı

Yazarlar:

Gonca Alan | Mevlüt Tercan

Yayıncı:

Ege University

Ana Başlıklar:

Wearable Materials

Dergi:

Textile and Apparel Vol.33 Issue 2, pp.176-184

Belge Tipi:

Makale

Yayın Tarihi:

6/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001293050

pISSN:

1300-3356