Joint Strength of PLA Sheets Produced by Additive Manufacturing: Comparison of Induction Heating and Adhesive Technologies

Mustafa Acaroğlu; Özkan Öz; Fatih Huzeyfe Öztürk

Makale detayları

Joint Strength of PLA Sheets Produced by Additive Manufacturing: Comparison of Induction Heating and Adhesive Technologies

Yazarlar:

Mustafa Acaroğlu | Özkan Öz | Fatih Huzeyfe Öztürk

Yayıncı:

Afyon Kocatepe University

Ana Başlıklar:

Makine Mühendisliği (Diğer)

Dergi:

Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi Vol.24 Issue 4, pp.993-1004

Belge Tipi:

Makale

Yayın Tarihi:

8/2024

Belge Dili:

Türkçe

Document ID (Org No.):

2001323274

pISSN:

2149-3367

Anahtar kelimeler:

Özet:

 In this study, the strengths of thermoplastic joints prepared using induction heating and industrial adhesive were experimentally determined. The Polylactic acid PLA sheets used in the joints were produced with a 3D printer and joined using adhesive and induction heating. In the induction heating process, the susceptor with different geometries wire and sheet was placed in the overlap region. In the adhesive bonding method, cyanoacrylate industrial adhesive was used on the overlap surfaces. Tensile tests were performed to determine the strength of the joints prepared by both methods. In the case of using a sheet, 3 wires and 5 wires as susceptor in the induction heating process, the joint failure loads were obtained as 1003 N, 1393 N and 2057 N, respectively. In the case of adhesive joint, the failure load reached 2378 N. The experimental results showed that it is more appropriate to use different numbers of wires instead of plates in the entire overlap zone in the induction heating method. In addition, the fact that the joint strength value achieved with 5 wires in induction heating is close to the joint strength value prepared using adhesive showed that this method could be an important alternative to adhesively bonded joints.

 In this study, the strengths of thermoplastic joints prepared using induction heating and industrial adhesive were experimentally determined. The Polylactic acid PLA sheets used in the joints were produced with a 3D printer and joined using adhesive and induction heating. In the induction heating process, the susceptor with different geometries wire and sheet was placed in the overlap region. In the adhesive bonding method, cyanoacrylate industrial adhesive was used on the overlap surfaces. Tensile tests were performed to determine the strength of the joints prepared by both methods. In the case of using a sheet, 3 wires and 5 wires as susceptor in the induction heating process, the joint failure loads were obtained as 1003 N, 1393 N and 2057 N, respectively. In the case of adhesive joint, the failure load reached 2378 N. The experimental results showed that it is more appropriate to use different numbers of wires instead of plates in the entire overlap zone in the induction heating method. In addition, the fact that the joint strength value achieved with 5 wires in induction heating is close to the joint strength value prepared using adhesive showed that this method could be an important alternative to adhesively bonded joints.

 In this study, the strengths of thermoplastic joints prepared using induction heating and industrial adhesive were experimentally determined. The Polylactic acid PLA sheets used in the joints were produced with a 3D printer and joined using adhesive and induction heating. In the induction heating process, the susceptor with different geometries wire and sheet was placed in the overlap region. In the adhesive bonding method, cyanoacrylate industrial adhesive was used on the overlap surfaces. Tensile tests were performed to determine the strength of the joints prepared by both methods. In the case of using a sheet, 3 wires and 5 wires as susceptor in the induction heating process, the joint failure loads were obtained as 1003 N, 1393 N and 2057 N, respectively. In the case of adhesive joint, the failure load reached 2378 N. The experimental results showed that it is more appropriate to use different numbers of wires instead of plates in the entire overlap zone in the induction heating method. In addition, the fact that the joint strength value achieved with 5 wires in induction heating is close to the joint strength value prepared using adhesive showed that this method could be an important alternative to adhesively bonded joints.

 Bu çalışmada indüksiyonlu ısıtma ve endüstriyel yapıştırıcı kullanılarak hazırlanan termoplastik malzemeli bağlantıların dayanımları deneysel olarak belirlenmiştir. Bağlantılarda kullanılan Polilaktik Asit PLA levhalar 3B yazıcı kullanılarak üretilmiş ve yapıştırma ve indüksiyonlu ısıtma yöntemleri ile birleştirilmiştir. İndüksiyonlu ısıtma prosesinde, bindirme bölgesine farklı geometrilerde tel ve levha iletken malzeme yerleştirilmiştir. Yapıştırıcı ile birleştirme yönteminde bindirme yüzeylerinde siyanoakrilat endüstriyel yapıştırıcı kullanılmıştır. Her iki yöntem ile hazırlanan bağlantıların dayanımlarını belirlemek için çekme testleri uygulanmıştır. İndüksiyonlu ısıtma prosesinde iletken malzeme olarak levha, 3 tel ve 5 tel kullanılması durumunda bağlantı hasar yükleri sırasıyla, 1003 N, 1393 N ve 2057 N olarak ölçülmüştür. Yapıştırmalı bağlantıda hasar yükü 2378 Na ulaşmıştır. Deneysel sonuçlar, indüksiyonlu ısıtma yönteminde bindirme bölgesinin tamamında levha yerine farklı sayılarda tel kullanımının daha uygun olduğunu göstermiştir. Ayrıca, indüksiyonlu ısıtmada 5 tel ile ulaşılan bağlantı dayanım değerinin, yapıştırıcı kullanılarak hazırlanan bağlantı dayanım değerine yakın olması, bu yöntemin yapıştırmalı bağlantılara önemli bir alternatif olabileceğini göstermiştir.

Makale detayları

Joint Strength of PLA Sheets Produced by Additive Manufacturing: Comparison of Induction Heating and Adhesive Technologies

Yazarlar:

Mustafa Acaroğlu | Özkan Öz | Fatih Huzeyfe Öztürk

Yayıncı:

Afyon Kocatepe University

Ana Başlıklar:

Makine Mühendisliği (Diğer)

Dergi:

Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi Vol.24 Issue 4, pp.993-1004

Belge Tipi:

Makale

Yayın Tarihi:

8/2024

Belge Dili:

Türkçe

Document ID (Org No.):

2001323274

pISSN:

2149-3367

Single lap joint

Joint strength

Induction heating

Additive manufacturingBasit bindirmeli bağlantı

Bağlantı dayanımı

İndüksiyonlu ısıtma

Eklemeli imalat.

Sayı

Makale detayları

Yazarlar: Mustafa Acaroğlu | Özkan Öz | Fatih Huzeyfe Öztürk

Yayıncı: Afyon Kocatepe University

Ana Başlıklar: Makine Mühendisliği (Diğer)

Dergi: Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi Vol.24 Issue 4, pp.993-1004

Belge Tipi: Makale

Yayın Tarihi: 8/2024

Belge Dili: Türkçe

Document ID (Org No.): 2001323274

pISSN: 2149-3367

Sayı

Yazarlar:

Mustafa Acaroğlu | Özkan Öz | Fatih Huzeyfe Öztürk

Yayıncı:

Afyon Kocatepe University

Ana Başlıklar:

Makine Mühendisliği (Diğer)

Dergi:

Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi Vol.24 Issue 4, pp.993-1004

Belge Tipi:

Makale

Yayın Tarihi:

8/2024

Belge Dili:

Türkçe

Document ID (Org No.):

2001323274

pISSN:

2149-3367