Effect of Edge Trimming Parameters on Surface Quality of Carbon Fiber Reinforced Polymer Composites

Ahmet CAN

Makale detayları

Effect of Edge Trimming Parameters on Surface Quality of Carbon Fiber Reinforced Polymer Composites

Yazarlar:

Ahmet CAN

Yayıncı:

Afyon Kocatepe University

Dergi:

Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi 2017 Vol.17 Issue 1, pp.302-311

Belge Tipi:

Makale

Yayın Tarihi:

4/2017

Belge Dili:

İngilizce

Document ID (Org No.):

2000846257

Sıklık:

İki Aylık

eISSN:

2149-3367

Anahtar kelimeler:

Özet:

 

The main focus of this paper is to investigate the surface quality and machinability of the edge trimming process of carbon fiber reinforced polymer (CFRP) material. Measurement of transverse and longitudinal surface roughness and deformation behavior are carried out for different combinations of cutting speed, feed per tooth, tool type and milling type to evaluate the machined surface quality. Three different flutes (2,4,6) micro grain carbide end mill tools were used for vertical and inclined peripheral milling. Edge trimming experiments were conducted under different experimental parameters and their levels according to the Taguchi design of experiment method. The contribution ratio of parameters on machinability outputs has statistically analyzed by Analysis of Variance (ANOVA). According to machinability outputs such as surface roughness and deformation types, the inclined peripheral milling is more suitable than vertical peripheral milling. Edge trimming by vertical peripheral milling generates Type II delamination which consists of long uncut fibers protruding from the trimmed edges. Edge trimming by inclined milling generates Type I-II delamination which consists of short uncut fibers protruding from the trimmed edges and where plies have broken inwards in the same time. The transverse and longitudinal surface roughness and deformation decreased with increased number of teeth, cutting speed and decreased feed per tooth. The best machining quality was obtained when cutting at the highest level of cutting speed, lowest feed rate and 6 number of flute in inclined milling.

Makale detayları

Effect of Edge Trimming Parameters on Surface Quality of Carbon Fiber Reinforced Polymer Composites

Yazarlar:

Ahmet CAN

Yayıncı:

Afyon Kocatepe University

Dergi:

Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi 2017 Vol.17 Issue 1, pp.302-311

Belge Tipi:

Makale

Yayın Tarihi:

4/2017

Belge Dili:

İngilizce

Document ID (Org No.):

2000846257

Sıklık:

İki Aylık

eISSN:

2149-3367

CFRP

Edge Trimming

Delamination

Taguchi

ANOVA

Surface Roughness

Sayı

Makale detayları

Effect of Edge Trimming Parameters on Surface Quality of Carbon Fiber Reinforced Polymer Composites

Yazarlar: Ahmet CAN

Yayıncı: Afyon Kocatepe University

Dergi: Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi 2017 Vol.17 Issue 1, pp.302-311

Belge Tipi: Makale

Yayın Tarihi: 4/2017

Belge Dili: İngilizce

Document ID (Org No.): 2000846257

Sıklık: İki Aylık

eISSN: 2149-3367

CFRP

Edge Trimming

Delamination

Taguchi

ANOVA

Surface Roughness

Sayı

Yazarlar:

Ahmet CAN

Yayıncı:

Afyon Kocatepe University

Dergi:

Afyon Kocatepe Üniversitesi Fen Ve Mühendislik Bilimleri Dergisi 2017 Vol.17 Issue 1, pp.302-311

Belge Tipi:

Makale

Yayın Tarihi:

4/2017

Belge Dili:

İngilizce

Document ID (Org No.):

2000846257

Sıklık:

İki Aylık

eISSN:

2149-3367