Numerical analysis of the effect of the evaporator inlet-outlet position on the PV-T performance

Ridvan Yakut

Makale detayları

Numerical analysis of the effect of the evaporator inlet-outlet position on the PV-T performance

Yazarlar:

Ridvan Yakut

Yayıncı:

Gumushane University

Ana Başlıklar:

Mühendislik

Dergi:

Gümüşhane Üniversitesi Fen Bilimleri Dergisi Vol.13 Issue 1, pp.145-159

Belge Tipi:

Makale

Yayın Tarihi:

1/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001282400

pISSN:

2146-538X

Anahtar kelimeler:

Özet:

 The increase in global energy consumption and carbon dioxide emissions increase the interest in renewable energy sources. Solar energy is at the forefront of renewable energy sources, and the decrease in cell efficiency due to various reasons during operation is an obstacle to this technology. Increasing the temperature of photovoltaic cells during operation causes a decrease in cell efficiency. Control of photovoltaic cells temperature is crucial in terms of both prolonging the economic life of the cells and increasing the efficiency of the system. The effect of the evaporator inlet and outlet position of the fluid on the heat transfer is known, but this effect was not examined in the studies carried out to increase the efficiency of the PV-T photovoltaicthermal system. In the current study, the system efficiency parameters and COP coefficient of performance values of a PV-T evaporator cooled by forced air circulation were investigated by CFD computational fluid dynamics analysis. The analyzes were carried out in a single array for three different flow rates 0.0125 kgs, 0.0250 kgs, 0.0500 kgs and nine different evaporator inlet-outlet positions CC, CL, CR, RC, RL, RR, LC, LL, LR, constant radiation of 1000 Wm2. It was determined that there is a total efficiency difference of over 20 and an overall COP difference of over 25 between the best and worst inlet-outlet positions. The highest total and thermal efficiency were obtained for the RR condition, and the highest electrical efficiency was obtained for the LR condition but in the long-term, the highest efficiency can be achieved with the LC design. In the study also the highest COP values were calculated for the CL condition and the worst COP values for the RR condition.

 The increase in global energy consumption and carbon dioxide emissions increase the interest in renewable energy sources. Solar energy is at the forefront of renewable energy sources, and the decrease in cell efficiency due to various reasons during operation is an obstacle to this technology. Increasing the temperature of photovoltaic cells during operation causes a decrease in cell efficiency. Control of photovoltaic cells temperature is crucial in terms of both prolonging the economic life of the cells and increasing the efficiency of the system. The effect of the evaporator inlet and outlet position of the fluid on the heat transfer is known, but this effect was not examined in the studies carried out to increase the efficiency of the PV-T photovoltaicthermal system. In the current study, the system efficiency parameters and COP coefficient of performance values of a PV-T evaporator cooled by forced air circulation were investigated by CFD computational fluid dynamics analysis. The analyzes were carried out in a single array for three different flow rates 0.0125 kgs, 0.0250 kgs, 0.0500 kgs and nine different evaporator inlet-outlet positions CC, CL, CR, RC, RL, RR, LC, LL, LR, constant radiation of 1000 Wm2. It was determined that there is a total efficiency difference of over 20 and an overall COP difference of over 25 between the best and worst inlet-outlet positions. The highest total and thermal efficiency were obtained for the RR condition, and the highest electrical efficiency was obtained for the LR condition but in the long-term, the highest efficiency can be achieved with the LC design. In the study also the highest COP values were calculated for the CL condition and the worst COP values for the RR condition.

 The increase in global energy consumption and carbon dioxide emissions increase the interest in renewable energy sources. Solar energy is at the forefront of renewable energy sources, and the decrease in cell efficiency due to various reasons during operation is an obstacle to this technology. Increasing the temperature of photovoltaic cells during operation causes a decrease in cell efficiency. Control of photovoltaic cells temperature is crucial in terms of both prolonging the economic life of the cells and increasing the efficiency of the system. The effect of the evaporator inlet and outlet position of the fluid on the heat transfer is known, but this effect was not examined in the studies carried out to increase the efficiency of the PV-T photovoltaicthermal system. In the current study, the system efficiency parameters and COP coefficient of performance values of a PV-T evaporator cooled by forced air circulation were investigated by CFD computational fluid dynamics analysis. The analyzes were carried out in a single array for three different flow rates 0.0125 kgs, 0.0250 kgs, 0.0500 kgs and nine different evaporator inlet-outlet positions CC, CL, CR, RC, RL, RR, LC, LL, LR, constant radiation of 1000 Wm2. It was determined that there is a total efficiency difference of over 20 and an overall COP difference of over 25 between the best and worst inlet-outlet positions. The highest total and thermal efficiency were obtained for the RR condition, and the highest electrical efficiency was obtained for the LR condition but in the long-term, the highest efficiency can be achieved with the LC design. In the study also the highest COP values were calculated for the CL condition and the worst COP values for the RR condition.

 Küresel enerji tüketimindeki ve karbondioksit emisyonlarındaki artış, yenilenebilir enerji kaynaklarına olan ilgiyi artırmaktadır. Yenilenebilir enerji kaynaklarının başında güneş enerjisi gelmektedir ve çalışma esnasında çeşitli sebeplerle hücre verimliliğinin düşmesi bu teknolojinin önündeki engeldir. Fotovoltaik hücrelerin çalışma sırasında sıcaklığının artması hücre veriminin düşmesine neden olmaktadır. Fotovoltaik hücre sıcaklığının kontrolü hem hücrelerin ekonomik ömrünü uzatmak hem de sistemin verimini artırmak açısından çok önemlidir. Akışkanın buharlaştırıcıya giriş ve çıkış konumunun ısı transferine etkisi bilinmektedir ancak PV-T fotovoltaik-termal sisteminin verimini artırmak için yürütülen çalışmalarda bu etki incelenmemiştir. Bu çalışmada, cebri hava sirkülasyonu ile soğutulan bir PV-T evaporatörün sistem verimlilik parametreleri ve COP performans katsayısı değerleri, HAD hesaplamalı akışkanlar dinamiği analizi ile incelenmiştir. Analizler, tek dizide, üç farklı debide 0.0125 kgs, 0.0250 kgs, 0.0500 kgs, dokuz farklı buharlaştırıcıya giriş-çıkış pozisyonu CC, CL, CR, RC, RL, RR, LC, LL, LR ve 1000 Wm2 sabit radyasyon için yürütülmüştür. En iyi ve en kötü giriş-çıkış konumları arasında 20nin üzerinde bir toplam verimlilik farkı ve 25in üzerinde bir genel COP farkı olduğu belirlenmiştir. En yüksek toplam ve termal verim RR koşulu için, en yüksek elektriksel verim LR koşulu için elde edilmiştir ancak uzun vadede en yüksek verim LC tasarımı ile elde edilebilmektedir. Çalışmada ayrıca CL koşulu için en yüksek COP değerleri ve RR koşulu için en kötü COP değerleri hesaplanmıştır.

Makale detayları

Numerical analysis of the effect of the evaporator inlet-outlet position on the PV-T performance

Yazarlar:

Ridvan Yakut

Yayıncı:

Gumushane University

Ana Başlıklar:

Mühendislik

Dergi:

Gümüşhane Üniversitesi Fen Bilimleri Dergisi Vol.13 Issue 1, pp.145-159

Belge Tipi:

Makale

Yayın Tarihi:

1/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001282400

pISSN:

2146-538X

CFD

COP

Electrical efficiency

Photovoltaic thermal collectors

Thermal efficiency

HAD

COP

Elektriksel verim

Fotovoltaik termal sistem

Termal verim

Sayı

Makale detayları

Yazarlar: Ridvan Yakut

Yayıncı: Gumushane University

Ana Başlıklar: Mühendislik

Dergi: Gümüşhane Üniversitesi Fen Bilimleri Dergisi Vol.13 Issue 1, pp.145-159

Belge Tipi: Makale

Yayın Tarihi: 1/2023

Belge Dili: İngilizce

Document ID (Org No.): 2001282400

pISSN: 2146-538X

Sayı

Yazarlar:

Ridvan Yakut

Yayıncı:

Gumushane University

Ana Başlıklar:

Mühendislik

Dergi:

Gümüşhane Üniversitesi Fen Bilimleri Dergisi Vol.13 Issue 1, pp.145-159

Belge Tipi:

Makale

Yayın Tarihi:

1/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001282400

pISSN:

2146-538X