Effects on Machinability of Minimum Quantity Lubrication Strategy during Milling of ST52 Steel

Serhat Şap

Makale detayları

Effects on Machinability of Minimum Quantity Lubrication Strategy during Milling of ST52 Steel

Yazarlar:

Serhat Şap

Yayıncı:

Bingol University

Ana Başlıklar:

Mühendislik

Dergi:

Türk Doğa ve Fen Dergisi Vol.12 Issue 1, pp.82-90

Belge Tipi:

Makale

Yayın Tarihi:

3/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001286038

pISSN:

2149-6366

Anahtar kelimeler:

Özet:

 This study focuses on milling under sustainable cutting conditions of ST52 steel, frequently used in the manufacturing industry. ST52 steel is a good candidate as a workpiece because it is inexpensive and readily available. To achieve sustainable conditions, the cutting zone minimum quantity lubrication technology was used during processing. The experiments used three cutting speeds 120-180-240 m min-1, three feed rates 0.12-0.18-0.24 mm rev-1, and a constant depth of cut 0.5 mm. Taguchi L9 orthogonal array was used to reduce repetitions. The response parameters are surface roughness, flank wear, and cutting temperature. As a result, when compared to the dry environment, the minimum quantity lubrication environment improved surface roughness by approximately 62.37, flank wear by approximately 9.95, and cutting temperature by approximately 13.82. In addition, the most effective control factors on response parameters were determined by statistical analysis.

 This study focuses on milling under sustainable cutting conditions of ST52 steel, frequently used in the manufacturing industry. ST52 steel is a good candidate as a workpiece because it is inexpensive and readily available. To achieve sustainable conditions, the cutting zone minimum quantity lubrication technology was used during processing. The experiments used three cutting speeds 120-180-240 m min-1, three feed rates 0.12-0.18-0.24 mm rev-1, and a constant depth of cut 0.5 mm. Taguchi L9 orthogonal array was used to reduce repetitions. The response parameters are surface roughness, flank wear, and cutting temperature. As a result, when compared to the dry environment, the minimum quantity lubrication environment improved surface roughness by approximately 62.37, flank wear by approximately 9.95, and cutting temperature by approximately 13.82. In addition, the most effective control factors on response parameters were determined by statistical analysis.

 This study focuses on milling under sustainable cutting conditions of ST52 steel, frequently used in the manufacturing industry. ST52 steel is a good candidate as a workpiece because it is inexpensive and readily available. To achieve sustainable conditions, the cutting zone minimum quantity lubrication technology was used during processing. The experiments used three cutting speeds 120-180-240 m min-1, three feed rates 0.12-0.18-0.24 mm rev-1, and a constant depth of cut 0.5 mm. Taguchi L9 orthogonal array was used to reduce repetitions. The response parameters are surface roughness, flank wear, and cutting temperature. As a result, when compared to the dry environment, the minimum quantity lubrication environment improved surface roughness by approximately 62.37, flank wear by approximately 9.95, and cutting temperature by approximately 13.82. In addition, the most effective control factors on response parameters were determined by statistical analysis.

 This study focuses on milling under sustainable cutting conditions of ST52 steel, frequently used in the manufacturing industry. ST52 steel is a good candidate as a workpiece because it is inexpensive and readily available. To achieve sustainable conditions, the cutting zone minimum quantity lubrication technology was used during processing. The experiments used three cutting speeds 120-180-240 m min-1, three feed rates 0.12-0.18-0.24 mm rev-1, and a constant depth of cut 0.5 mm. Taguchi L9 orthogonal array was used to reduce repetitions. The response parameters are surface roughness, flank wear, and cutting temperature. As a result, when compared to the dry environment, the minimum quantity lubrication environment improved surface roughness by approximately 62.37, flank wear by approximately 9.95, and cutting temperature by approximately 13.82. In addition, the most effective control factors on response parameters were determined by statistical analysis.

Makale detayları

Effects on Machinability of Minimum Quantity Lubrication Strategy during Milling of ST52 Steel

Yazarlar:

Serhat Şap

Yayıncı:

Bingol University

Ana Başlıklar:

Mühendislik

Dergi:

Türk Doğa ve Fen Dergisi Vol.12 Issue 1, pp.82-90

Belge Tipi:

Makale

Yayın Tarihi:

3/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001286038

pISSN:

2149-6366

ST52 steel

Machinability

Minimum quantity lubrication

Taguchi technique

ST52 steel

Machinability

Minimum quantity lubrication

Taguchi technique

Sayı

Makale detayları

Yazarlar: Serhat Şap

Yayıncı: Bingol University

Ana Başlıklar: Mühendislik

Dergi: Türk Doğa ve Fen Dergisi Vol.12 Issue 1, pp.82-90

Belge Tipi: Makale

Yayın Tarihi: 3/2023

Belge Dili: İngilizce

Document ID (Org No.): 2001286038

pISSN: 2149-6366

Sayı

Yazarlar:

Serhat Şap

Yayıncı:

Bingol University

Ana Başlıklar:

Mühendislik

Dergi:

Türk Doğa ve Fen Dergisi Vol.12 Issue 1, pp.82-90

Belge Tipi:

Makale

Yayın Tarihi:

3/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001286038

pISSN:

2149-6366