Investigation into the heat sink performance of the inline and cut cross fins types using different aluminum alloys

Ibrahim Thamer Nazzal; Saad Farhan

Makale detayları

Investigation into the heat sink performance of the inline and cut cross fins types using different aluminum alloys

Yazarlar:

Ibrahim Thamer Nazzal | Saad Farhan

Yayıncı:

Yildiz Technical University

Ana Başlıklar:

Thermodynamics and Statistical Physics

Dergi:

Journal of Thermal Engineering Vol.10 Issue 1, pp.10-20

Belge Tipi:

Makale

Yayın Tarihi:

1/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001311214

pISSN:

2148-7847

Anahtar kelimeler:

Özet:

 In this study, two types of heat sinks are selected at similar dimensions. In addition, five types of aluminum alloys are used to find the optimum performance for both models inline and cut cross heat sinks. These types of alloy materials were Al-1100, Al-3063, Al25Ni, and Al25Cu that are selected and compared with pure aluminum. The effectiveness results showed of the heat sink using Al- 25Cu has the highest value compared to the other material types Al- 25Ni, Al 1100, and Al 6063 respectively. While the lowest value of the fin efficiency was observed for pure aluminum. Moreover, the heat sink using Al- 25Ni, Al 1100, and Al 6063 has moderate values. The results also indicated that the rate of heat-dissipated from the cut cross heat sink increases, as the fin thickness increases until reaches maximum value be-fore it decreases with an increase in the fin thickness. While for the inline heat sink, the heat transfer increases as the fin thickness increase before stables at 2 mm approximately.

 In this study, two types of heat sinks are selected at similar dimensions. In addition, five types of aluminum alloys are used to find the optimum performance for both models inline and cut cross heat sinks. These types of alloy materials were Al-1100, Al-3063, Al25Ni, and Al25Cu that are selected and compared with pure aluminum. The effectiveness results showed of the heat sink using Al- 25Cu has the highest value compared to the other material types Al- 25Ni, Al 1100, and Al 6063 respectively. While the lowest value of the fin efficiency was observed for pure aluminum. Moreover, the heat sink using Al- 25Ni, Al 1100, and Al 6063 has moderate values. The results also indicated that the rate of heat-dissipated from the cut cross heat sink increases, as the fin thickness increases until reaches maximum value be-fore it decreases with an increase in the fin thickness. While for the inline heat sink, the heat transfer increases as the fin thickness increase before stables at 2 mm approximately.

 In this study, two types of heat sinks are selected at similar dimensions. In addition, five types of aluminum alloys are used to find the optimum performance for both models inline and cut cross heat sinks. These types of alloy materials were Al-1100, Al-3063, Al25Ni, and Al25Cu that are selected and compared with pure aluminum. The effectiveness results showed of the heat sink using Al- 25Cu has the highest value compared to the other material types Al- 25Ni, Al 1100, and Al 6063 respectively. While the lowest value of the fin efficiency was observed for pure aluminum. Moreover, the heat sink using Al- 25Ni, Al 1100, and Al 6063 has moderate values. The results also indicated that the rate of heat-dissipated from the cut cross heat sink increases, as the fin thickness increases until reaches maximum value be-fore it decreases with an increase in the fin thickness. While for the inline heat sink, the heat transfer increases as the fin thickness increase before stables at 2 mm approximately.

 In this study, two types of heat sinks are selected at similar dimensions. In addition, five types of aluminum alloys are used to find the optimum performance for both models inline and cut cross heat sinks. These types of alloy materials were Al-1100, Al-3063, Al25Ni, and Al25Cu that are selected and compared with pure aluminum. The effectiveness results showed of the heat sink using Al- 25Cu has the highest value compared to the other material types Al- 25Ni, Al 1100, and Al 6063 respectively. While the lowest value of the fin efficiency was observed for pure aluminum. Moreover, the heat sink using Al- 25Ni, Al 1100, and Al 6063 has moderate values. The results also indicated that the rate of heat-dissipated from the cut cross heat sink increases, as the fin thickness increases until reaches maximum value be-fore it decreases with an increase in the fin thickness. While for the inline heat sink, the heat transfer increases as the fin thickness increase before stables at 2 mm approximately.

Makale detayları

Investigation into the heat sink performance of the inline and cut cross fins types using different aluminum alloys

Yazarlar:

Ibrahim Thamer Nazzal | Saad Farhan

Yayıncı:

Yildiz Technical University

Ana Başlıklar:

Thermodynamics and Statistical Physics

Dergi:

Journal of Thermal Engineering Vol.10 Issue 1, pp.10-20

Belge Tipi:

Makale

Yayın Tarihi:

1/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001311214

pISSN:

2148-7847

Inline

Cut Cross

Passive Heat Sink

Aluminum Alloys

Sayı

Makale detayları

Investigation into the heat sink performance of the inline and cut cross fins types using different aluminum alloys

Yazarlar: Ibrahim Thamer Nazzal | Saad Farhan

Yayıncı: Yildiz Technical University

Ana Başlıklar: Thermodynamics and Statistical Physics

Dergi: Journal of Thermal Engineering Vol.10 Issue 1, pp.10-20

Belge Tipi: Makale

Yayın Tarihi: 1/2024

Belge Dili: İngilizce

Document ID (Org No.): 2001311214

pISSN: 2148-7847

Inline

Cut Cross

Passive Heat Sink

Aluminum Alloys

Sayı

Yazarlar:

Ibrahim Thamer Nazzal | Saad Farhan

Yayıncı:

Yildiz Technical University

Ana Başlıklar:

Thermodynamics and Statistical Physics

Dergi:

Journal of Thermal Engineering Vol.10 Issue 1, pp.10-20

Belge Tipi:

Makale

Yayın Tarihi:

1/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001311214

pISSN:

2148-7847