Experimental investigation and FEM analysis of chip morphology in the turning of ASTM F-75 CoCrMo alloy

Ender Emir; Burak Özdemir; Erkan Bahçe

Makale detayları

Experimental investigation and FEM analysis of chip morphology in the turning of ASTM F-75 CoCrMo alloy

Yazarlar:

Ender Emir | Burak Özdemir | Erkan Bahçe

Yayıncı:

Yildiz Technical University

Ana Başlıklar:

Computer Software

Dergi:

Sigma Journal of Engineering and Natural Sciences Vol.42 Issue 3, pp.679-691

Belge Tipi:

Makale

Yayın Tarihi:

12/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001319372

pISSN:

1304-7191

Anahtar kelimeler:

Özet:

 During the machining process, problems such as tool wear, high temperature, force distribu-tion, and surface quality deterioration must be fully understood. Control of these problems with experimental studies and numerical analyses is important in ensuring dimensional ac-curacy and surface integrity of the cutting tool, workpiece, and also the finished product. The aim of this study is to investigate the effects of machining parameters on chip morphology, residual stresses and tool wear in turning operations of ASTM-F75 CoCrMo alloy experi-mentally and by finite element method FEM simulation. The study was carried out at three different feed rates 0.1, 0.2, 0.3 mmrev and at a constant cutting speed of 80 mmin both experimentally on a CNC turning machine and with FEM simulation. From the obtained re-sults, the formation of cracks and adhesions on the surfaces of the chip were observed due to the increase of the feed rate. According to the orthogonal cutting model, chip height ratio Gs and tooth pitch Pc values of saw-tooth chips supported each other with measurements taken from both FEM images and experimental images. With the increase of the forward speed, the Gs ratio decreased, while the Pc increased. In addition, microscopic images obtained from the cutting tool also showed that the rate of crater wear gradually increased with increasing feed rate. As a result, it is seen that machining parameters have a significant effect on cutting tool and chip morphology in CoCrMo ASTM-F75 alloy turning.

 During the machining process, problems such as tool wear, high temperature, force distribu-tion, and surface quality deterioration must be fully understood. Control of these problems with experimental studies and numerical analyses is important in ensuring dimensional ac-curacy and surface integrity of the cutting tool, workpiece, and also the finished product. The aim of this study is to investigate the effects of machining parameters on chip morphology, residual stresses and tool wear in turning operations of ASTM-F75 CoCrMo alloy experi-mentally and by finite element method FEM simulation. The study was carried out at three different feed rates 0.1, 0.2, 0.3 mmrev and at a constant cutting speed of 80 mmin both experimentally on a CNC turning machine and with FEM simulation. From the obtained re-sults, the formation of cracks and adhesions on the surfaces of the chip were observed due to the increase of the feed rate. According to the orthogonal cutting model, chip height ratio Gs and tooth pitch Pc values of saw-tooth chips supported each other with measurements taken from both FEM images and experimental images. With the increase of the forward speed, the Gs ratio decreased, while the Pc increased. In addition, microscopic images obtained from the cutting tool also showed that the rate of crater wear gradually increased with increasing feed rate. As a result, it is seen that machining parameters have a significant effect on cutting tool and chip morphology in CoCrMo ASTM-F75 alloy turning.

 During the machining process, problems such as tool wear, high temperature, force distribu-tion, and surface quality deterioration must be fully understood. Control of these problems with experimental studies and numerical analyses is important in ensuring dimensional ac-curacy and surface integrity of the cutting tool, workpiece, and also the finished product. The aim of this study is to investigate the effects of machining parameters on chip morphology, residual stresses and tool wear in turning operations of ASTM-F75 CoCrMo alloy experi-mentally and by finite element method FEM simulation. The study was carried out at three different feed rates 0.1, 0.2, 0.3 mmrev and at a constant cutting speed of 80 mmin both experimentally on a CNC turning machine and with FEM simulation. From the obtained re-sults, the formation of cracks and adhesions on the surfaces of the chip were observed due to the increase of the feed rate. According to the orthogonal cutting model, chip height ratio Gs and tooth pitch Pc values of saw-tooth chips supported each other with measurements taken from both FEM images and experimental images. With the increase of the forward speed, the Gs ratio decreased, while the Pc increased. In addition, microscopic images obtained from the cutting tool also showed that the rate of crater wear gradually increased with increasing feed rate. As a result, it is seen that machining parameters have a significant effect on cutting tool and chip morphology in CoCrMo ASTM-F75 alloy turning.

 During the machining process, problems such as tool wear, high temperature, force distribu-tion, and surface quality deterioration must be fully understood. Control of these problems with experimental studies and numerical analyses is important in ensuring dimensional ac-curacy and surface integrity of the cutting tool, workpiece, and also the finished product. The aim of this study is to investigate the effects of machining parameters on chip morphology, residual stresses and tool wear in turning operations of ASTM-F75 CoCrMo alloy experi-mentally and by finite element method FEM simulation. The study was carried out at three different feed rates 0.1, 0.2, 0.3 mmrev and at a constant cutting speed of 80 mmin both experimentally on a CNC turning machine and with FEM simulation. From the obtained re-sults, the formation of cracks and adhesions on the surfaces of the chip were observed due to the increase of the feed rate. According to the orthogonal cutting model, chip height ratio Gs and tooth pitch Pc values of saw-tooth chips supported each other with measurements taken from both FEM images and experimental images. With the increase of the forward speed, the Gs ratio decreased, while the Pc increased. In addition, microscopic images obtained from the cutting tool also showed that the rate of crater wear gradually increased with increasing feed rate. As a result, it is seen that machining parameters have a significant effect on cutting tool and chip morphology in CoCrMo ASTM-F75 alloy turning.

Makale detayları

Experimental investigation and FEM analysis of chip morphology in the turning of ASTM F-75 CoCrMo alloy

Yazarlar:

Ender Emir | Burak Özdemir | Erkan Bahçe

Yayıncı:

Yildiz Technical University

Ana Başlıklar:

Computer Software

Dergi:

Sigma Journal of Engineering and Natural Sciences Vol.42 Issue 3, pp.679-691

Belge Tipi:

Makale

Yayın Tarihi:

12/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001319372

pISSN:

1304-7191

ASTM-F75 CoCrMo Alloy

Chip Morphology Modelling

FEM

Turning

Sayı

Makale detayları

Experimental investigation and FEM analysis of chip morphology in the turning of ASTM F-75 CoCrMo alloy

Yazarlar: Ender Emir | Burak Özdemir | Erkan Bahçe

Yayıncı: Yildiz Technical University

Ana Başlıklar: Computer Software

Dergi: Sigma Journal of Engineering and Natural Sciences Vol.42 Issue 3, pp.679-691

Belge Tipi: Makale

Yayın Tarihi: 12/2024

Belge Dili: İngilizce

Document ID (Org No.): 2001319372

pISSN: 1304-7191

ASTM-F75 CoCrMo Alloy

Chip Morphology Modelling

FEM

Turning

Sayı

Yazarlar:

Ender Emir | Burak Özdemir | Erkan Bahçe

Yayıncı:

Yildiz Technical University

Ana Başlıklar:

Computer Software

Dergi:

Sigma Journal of Engineering and Natural Sciences Vol.42 Issue 3, pp.679-691

Belge Tipi:

Makale

Yayın Tarihi:

12/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001319372

pISSN:

1304-7191