Production of B4C Reinforced Composite Materials and Investigation of Their Bending Strength

Halit Doğan; Yılmaz Mutlu

Makale detayları

Production of B4C Reinforced Composite Materials and Investigation of Their Bending Strength

Yazarlar:

Halit Doğan | Yılmaz Mutlu

Yayıncı:

Çanakkale Onsekiz Mart University

Ana Başlıklar:

Mechanical Engineering

Dergi:

Journal of Advanced Research in Natural and Applied Sciences Vol.9 Issue 2, pp.323-330

Belge Tipi:

Makale

Yayın Tarihi:

6/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001291642

pISSN:

2757-5195

Anahtar kelimeler:

Özet:

 In this study, AA2024 aluminum alloy was selected as the matrix material, while B4C was selected as the reinforcement material, and particle-reinforced Al-matrix composite materials were produced using the powder metallurgy method. Examinations were made to determine the effects of different reinforcement particle ratios and sintering temperatures on the mechanical properties of the AA2024 matrix composite materials that were produced. The powders were compressed in a metal mold at room temperature and a pressure of 525 MPa under a uniaxial press. The raw specimens that were obtained were sintered for 45 minutes at different temperatures. The produced composite materials were subjected to three-point bending tests and hardness measurements. Optical microscopy analysis was carried out for characterization. The results allowed us to draw a conclusion on how the reinforcement material in the produced specimens affected Al-matrix composite properties. It was determined that the B4C reinforcement added to the matrix increased the hardness values of the composites at all sintering temperatures, the highest bending strength was obtained in the composite with 10 B4C particle reinforcement, and in general, the B4C reinforcement was homogeneously dispersed in the matrix. Increased B4C reinforcement ratios resulted in higher hardness values in the composite materials.

 In this study, AA2024 aluminum alloy was selected as the matrix material, while B4C was selected as the reinforcement material, and particle-reinforced Al-matrix composite materials were produced using the powder metallurgy method. Examinations were made to determine the effects of different reinforcement particle ratios and sintering temperatures on the mechanical properties of the AA2024 matrix composite materials that were produced. The powders were compressed in a metal mold at room temperature and a pressure of 525 MPa under a uniaxial press. The raw specimens that were obtained were sintered for 45 minutes at different temperatures. The produced composite materials were subjected to three-point bending tests and hardness measurements. Optical microscopy analysis was carried out for characterization. The results allowed us to draw a conclusion on how the reinforcement material in the produced specimens affected Al-matrix composite properties. It was determined that the B4C reinforcement added to the matrix increased the hardness values of the composites at all sintering temperatures, the highest bending strength was obtained in the composite with 10 B4C particle reinforcement, and in general, the B4C reinforcement was homogeneously dispersed in the matrix. Increased B4C reinforcement ratios resulted in higher hardness values in the composite materials.

 In this study, AA2024 aluminum alloy was selected as the matrix material, while B4C was selected as the reinforcement material, and particle-reinforced Al-matrix composite materials were produced using the powder metallurgy method. Examinations were made to determine the effects of different reinforcement particle ratios and sintering temperatures on the mechanical properties of the AA2024 matrix composite materials that were produced. The powders were compressed in a metal mold at room temperature and a pressure of 525 MPa under a uniaxial press. The raw specimens that were obtained were sintered for 45 minutes at different temperatures. The produced composite materials were subjected to three-point bending tests and hardness measurements. Optical microscopy analysis was carried out for characterization. The results allowed us to draw a conclusion on how the reinforcement material in the produced specimens affected Al-matrix composite properties. It was determined that the B4C reinforcement added to the matrix increased the hardness values of the composites at all sintering temperatures, the highest bending strength was obtained in the composite with 10 B4C particle reinforcement, and in general, the B4C reinforcement was homogeneously dispersed in the matrix. Increased B4C reinforcement ratios resulted in higher hardness values in the composite materials.

 In this study, AA2024 aluminum alloy was selected as the matrix material, while B4C was selected as the reinforcement material, and particle-reinforced Al-matrix composite materials were produced using the powder metallurgy method. Examinations were made to determine the effects of different reinforcement particle ratios and sintering temperatures on the mechanical properties of the AA2024 matrix composite materials that were produced. The powders were compressed in a metal mold at room temperature and a pressure of 525 MPa under a uniaxial press. The raw specimens that were obtained were sintered for 45 minutes at different temperatures. The produced composite materials were subjected to three-point bending tests and hardness measurements. Optical microscopy analysis was carried out for characterization. The results allowed us to draw a conclusion on how the reinforcement material in the produced specimens affected Al-matrix composite properties. It was determined that the B4C reinforcement added to the matrix increased the hardness values of the composites at all sintering temperatures, the highest bending strength was obtained in the composite with 10 B4C particle reinforcement, and in general, the B4C reinforcement was homogeneously dispersed in the matrix. Increased B4C reinforcement ratios resulted in higher hardness values in the composite materials.

Makale detayları

Production of B4C Reinforced Composite Materials and Investigation of Their Bending Strength

Yazarlar:

Halit Doğan | Yılmaz Mutlu

Yayıncı:

Çanakkale Onsekiz Mart University

Ana Başlıklar:

Mechanical Engineering

Dergi:

Journal of Advanced Research in Natural and Applied Sciences Vol.9 Issue 2, pp.323-330

Belge Tipi:

Makale

Yayın Tarihi:

6/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001291642

pISSN:

2757-5195

Aluminum Alloys

Sintering

Powder Metallurgy

Reinforcement Particle Ratio.

Composite Materials,

Sayı

Makale detayları

Production of B4C Reinforced Composite Materials and Investigation of Their Bending Strength

Yazarlar: Halit Doğan | Yılmaz Mutlu

Yayıncı: Çanakkale Onsekiz Mart University

Ana Başlıklar: Mechanical Engineering

Dergi: Journal of Advanced Research in Natural and Applied Sciences Vol.9 Issue 2, pp.323-330

Belge Tipi: Makale

Yayın Tarihi: 6/2023

Belge Dili: İngilizce

Document ID (Org No.): 2001291642

pISSN: 2757-5195

Aluminum Alloys

Sintering

Powder Metallurgy

Reinforcement Particle Ratio.

Composite Materials,

Sayı

Yazarlar:

Halit Doğan | Yılmaz Mutlu

Yayıncı:

Çanakkale Onsekiz Mart University

Ana Başlıklar:

Mechanical Engineering

Dergi:

Journal of Advanced Research in Natural and Applied Sciences Vol.9 Issue 2, pp.323-330

Belge Tipi:

Makale

Yayın Tarihi:

6/2023

Belge Dili:

İngilizce

Document ID (Org No.):

2001291642

pISSN:

2757-5195