Software Development for Processing Data from the Wear Testing Machine

Lutuf Ertürk; Burhan Selçuk

Makale detayları

Software Development for Processing Data from the Wear Testing Machine

Yazarlar:

Lutuf Ertürk | Burhan Selçuk

Yayıncı:

Kirikkale University

Ana Başlıklar:

Machine Design and Machine Equipment | Tribology

Dergi:

International Journal of Engineering Research and Development Vol.16 Issue 1, pp.267-278

Belge Tipi:

Makale

Yayın Tarihi:

1/2024

Belge Dili:

Türkçe

Document ID (Org No.):

2001310749

pISSN:

1308-5506

Anahtar kelimeler:

Özet:

 Microcontrollers are needed to receive and process data from a device. Microcontrollers have found widespread use in homes, offices and research environments. Although there are many systems available for programming microcontrollers, Arduino can be said to be more common in this regard. Arduino, which has open source hardware and software and a user interactive community, has been producing microcontroller-based Arduino boards since 2005. There are many systems designed with Arduino in the literature. In this study, it is aimed to receive and process data from the analog signal outputs of the Friction and Wear Testing Machine by using the Arduino Nano development board. To transfer and process data between Arduino and the computer, the open source Lazarus application, in which the Object Pascal language compiler is integrated, was used. As a result of wear, not only mass loss but also dimensional changes and surface damage may occur in machine parts. For this reason, wear is very important for the continuity and quality of production. In order to minimize the amount of wear, the parameters that cause wear must be examined. Therefore, the developed program is very important for examining wear parameters.

 Microcontrollers are needed to receive and process data from a device. Microcontrollers have found widespread use in homes, offices and research environments. Although there are many systems available for programming microcontrollers, Arduino can be said to be more common in this regard. Arduino, which has open source hardware and software and a user interactive community, has been producing microcontroller-based Arduino boards since 2005. There are many systems designed with Arduino in the literature. In this study, it is aimed to receive and process data from the analog signal outputs of the Friction and Wear Testing Machine by using the Arduino Nano development board. To transfer and process data between Arduino and the computer, the open source Lazarus application, in which the Object Pascal language compiler is integrated, was used. As a result of wear, not only mass loss but also dimensional changes and surface damage may occur in machine parts. For this reason, wear is very important for the continuity and quality of production. In order to minimize the amount of wear, the parameters that cause wear must be examined. Therefore, the developed program is very important for examining wear parameters.

 Microcontrollers are needed to receive and process data from a device. Microcontrollers have found widespread use in homes, offices and research environments. Although there are many systems available for programming microcontrollers, Arduino can be said to be more common in this regard. Arduino, which has open source hardware and software and a user interactive community, has been producing microcontroller-based Arduino boards since 2005. There are many systems designed with Arduino in the literature. In this study, it is aimed to receive and process data from the analog signal outputs of the Friction and Wear Testing Machine by using the Arduino Nano development board. To transfer and process data between Arduino and the computer, the open source Lazarus application, in which the Object Pascal language compiler is integrated, was used. As a result of wear, not only mass loss but also dimensional changes and surface damage may occur in machine parts. For this reason, wear is very important for the continuity and quality of production. In order to minimize the amount of wear, the parameters that cause wear must be examined. Therefore, the developed program is very important for examining wear parameters.

 Bir cihazdan verilerin alınıp işlenmesi için mikrodenetleyicilere ihtiyaç duyulur. Mikrodenetleyiciler evlerde, ofislerde ve araştırma ortamlarında yaygın kullanım alanı bulmuştur. Mikrodenetleyicileri programlamak için birçok sistem mevcut olsa da, Arduinonun bu konuda daha yaygın olduğu söylenebilir. Açık kaynaklı bir donanım ve yazılıma sahip olması ve kullanıcı etkileşimli topluluğu olan Arduino, 2005 yılından bu yana mikro denetleyici tabanlı Arduino kartları üretmektedir. Literatürde Arduino ile tasarlanan birçok sistem vardır. Bu çalışmada ise Arduino Nano geliştirme kartı kullanılarak, Sürtünme ve Aşınma Test Cihazının analog sinyal çıkışlarından verilerin alınıp işlenilmesi amaçlanmıştır. Arduino ile bilgisayar arasında verilerin aktarımı ve işlenmesi için Object Pascal dilinde derleyicinin entegre olduğu, açık kaynak kodlu Lazarus uygulaması kullanılmıştır. Aşınma sonucu makine parçalarında yalnızca kütle kaybı değil, boyutsal değişimler ve yüzey hasarları da oluşabilir. Bu nedenle aşınma, üretimin sürekliliği ve kalitesi bakımından oldukça önem arz etmektedir. Aşınma miktarını en aza indirmek için, aşınmaya neden olan parametrelerin incelenmesi gerekmektedir. Bu nedenle, geliştirilen program aşınma parametrelerinin incelenmesi açısından oldukça önemlidir.

Makale detayları

Software Development for Processing Data from the Wear Testing Machine

Yazarlar:

Lutuf Ertürk | Burhan Selçuk

Yayıncı:

Kirikkale University

Ana Başlıklar:

Machine Design and Machine Equipment | Tribology

Dergi:

International Journal of Engineering Research and Development Vol.16 Issue 1, pp.267-278

Belge Tipi:

Makale

Yayın Tarihi:

1/2024

Belge Dili:

Türkçe

Document ID (Org No.):

2001310749

pISSN:

1308-5506

Wear test

Friction coefficient

Machine

Arduino

Lazarus programming

Software developmentAşınma testi

Sürtünme katsayısı

Makine

Arduino

Lazarus programlama

Program geliştirme

Sayı

Makale detayları

Yazarlar: Lutuf Ertürk | Burhan Selçuk

Yayıncı: Kirikkale University

Ana Başlıklar: Machine Design and Machine Equipment | Tribology

Dergi: International Journal of Engineering Research and Development Vol.16 Issue 1, pp.267-278

Belge Tipi: Makale

Yayın Tarihi: 1/2024

Belge Dili: Türkçe

Document ID (Org No.): 2001310749

pISSN: 1308-5506

Sayı

Yazarlar:

Lutuf Ertürk | Burhan Selçuk

Yayıncı:

Kirikkale University

Ana Başlıklar:

Machine Design and Machine Equipment | Tribology

Dergi:

International Journal of Engineering Research and Development Vol.16 Issue 1, pp.267-278

Belge Tipi:

Makale

Yayın Tarihi:

1/2024

Belge Dili:

Türkçe

Document ID (Org No.):

2001310749

pISSN:

1308-5506