Effects of Different Splicing Methods on Conveyor Belt Strength

Savaş KİRENLİ; Recep DEMİRSÖZ

doi:https://doi.org/10.36222/ejt.1086915

Makale detayları

Effects of Different Splicing Methods on Conveyor Belt Strength

Yazarlar:

Savaş KİRENLİ | Recep DEMİRSÖZ

Yayıncı:

Hibetullah KILIÇ

Ana Başlıklar:

Diğer mühendislik dalları

Dergi:

European Journal of Technique (EJT) 2022 Vol.12 Issue 1, pp.22-29

Belge Tipi:

Makale

Yayın Tarihi:

6/2022

Belge Dili:

İngilizce

Document ID (Org No.):

2000425400

eISSN:

2536-5134

pISSN:

2536-5010

DOI:

https://doi.org/10.36222/ejt.1086915

Özet:

 

Conveyor belts are mechanisms that provide continuous transfer of any product from one place to another. Belt conveyor systems are at the forefront of the systems that minimize the need for people in the transportation of materials. In this way, it is inevitable to achieve both time and cost savings. With the continuous development of today's technology, it develops in the improvements in belt conveyor systems. Owing to the innovations and improvements in the conveyor belts, it becomes possible to minimize the maintenance, repair and undesired stoppages of the facilities. In this study, specimens extracted from a conveyor belt with a width of 800 mm, with a tensile strength of 45 N/mm2, 4 layers of polyester-polyamide blend cord fabric, 6 mm rubber bottom coating thickness and 3 mm rubber top coating thickness were used. The specimens were taken in three different ways (from the unspliced belt, from the mechanically spliced belt and from the vulcanized belt). The specimens taken from the spliced conveyor belts were subjected to the tensile test. The strength values of the belt specimens, from high to low, are in the form of unspliced belt, vulcanized belt and mechanically spliced belt. Among these applications, it has been observed that the mechanical splicing method is easier in terms of application than other splicing methods. It has been observed that the time required for maintenance and repair of the mechanical splicing method is between 1 and 2 hours, and the time required for the splicing method with vulcanization is between 6 and 8 hours. It has been understood that the mechanical method is advantageous over the vulcanization method in terms of the application time of the belt splicing method.

Makale detayları

Effects of Different Splicing Methods on Conveyor Belt Strength

Yazarlar: Savaş KİRENLİ | Recep DEMİRSÖZ

Yayıncı: Hibetullah KILIÇ

Ana Başlıklar: Diğer mühendislik dalları

Dergi: European Journal of Technique (EJT) 2022 Vol.12 Issue 1, pp.22-29

Belge Tipi: Makale

Yayın Tarihi: 6/2022

Belge Dili: İngilizce

Document ID (Org No.): 2000425400

eISSN: 2536-5134

pISSN: 2536-5010

DOI: https://doi.org/10.36222/ejt.1086915

Sayı

Yazarlar:

Savaş KİRENLİ | Recep DEMİRSÖZ

Yayıncı:

Hibetullah KILIÇ

Ana Başlıklar:

Diğer mühendislik dalları

Dergi:

European Journal of Technique (EJT) 2022 Vol.12 Issue 1, pp.22-29

Belge Tipi:

Makale

Yayın Tarihi:

6/2022

Belge Dili:

İngilizce

Document ID (Org No.):

2000425400

eISSN:

2536-5134

pISSN:

2536-5010

DOI:

https://doi.org/10.36222/ejt.1086915