Investigation of the Effect of Mechanical Alloying on the Wear Behavior of AA7020/Fe3O4/GNP Hybrid Composite Materials

Ufuk Taşcı

Makale detayları

Investigation of the Effect of Mechanical Alloying on the Wear Behavior of AA7020/Fe3O4/GNP Hybrid Composite Materials

Yazarlar:

Ufuk Taşcı

Yayıncı:

Gazi University

Ana Başlıklar:

Powder Metallurgy

Dergi:

Gazi University Journal of Science Part A: Engineering and Innovation Vol.11 Issue 4, pp.814-825

Belge Tipi:

Makale

Yayın Tarihi:

12/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001336828

pISSN:

2147-9542

Anahtar kelimeler:

Özet:

 In this study, the mechanical properties of compositehybrid composites were investigated by reinforcing 10 Fe3O4 and 0.25 nanographene by weight into the AA7020 alloy, which is widely preferred, especially in the defense and aviation industries. The prepared mixture powders were subjected to a mechanical alloying process for 1 and 8 hours in a ball mill with a 116 powder-ball ratio to distribute them homogeneously. The mixed hybridcomposite powders were produced in a metal mold using a powder metallurgy hot pressing method at 250 MPa load and 575C temperature for 60 minutes. The microstructural properties of the test samples were investigatedIn addition, density, microhardness and wear test results were examined in terms of mechanical properties. The hybrid sample with 8h mechanical alloying obtained the highest hardness value 118.5 HV and the lowest friction coefficient 0.1965 µm.

 In this study, the mechanical properties of compositehybrid composites were investigated by reinforcing 10 Fe3O4 and 0.25 nanographene by weight into the AA7020 alloy, which is widely preferred, especially in the defense and aviation industries. The prepared mixture powders were subjected to a mechanical alloying process for 1 and 8 hours in a ball mill with a 116 powder-ball ratio to distribute them homogeneously. The mixed hybridcomposite powders were produced in a metal mold using a powder metallurgy hot pressing method at 250 MPa load and 575C temperature for 60 minutes. The microstructural properties of the test samples were investigatedIn addition, density, microhardness and wear test results were examined in terms of mechanical properties. The hybrid sample with 8h mechanical alloying obtained the highest hardness value 118.5 HV and the lowest friction coefficient 0.1965 µm.

 In this study, the mechanical properties of compositehybrid composites were investigated by reinforcing 10 Fe3O4 and 0.25 nanographene by weight into the AA7020 alloy, which is widely preferred, especially in the defense and aviation industries. The prepared mixture powders were subjected to a mechanical alloying process for 1 and 8 hours in a ball mill with a 116 powder-ball ratio to distribute them homogeneously. The mixed hybridcomposite powders were produced in a metal mold using a powder metallurgy hot pressing method at 250 MPa load and 575C temperature for 60 minutes. The microstructural properties of the test samples were investigatedIn addition, density, microhardness and wear test results were examined in terms of mechanical properties. The hybrid sample with 8h mechanical alloying obtained the highest hardness value 118.5 HV and the lowest friction coefficient 0.1965 µm.

 In this study, the mechanical properties of compositehybrid composites were investigated by reinforcing 10 Fe3O4 and 0.25 nanographene by weight into the AA7020 alloy, which is widely preferred, especially in the defense and aviation industries. The prepared mixture powders were subjected to a mechanical alloying process for 1 and 8 hours in a ball mill with a 116 powder-ball ratio to distribute them homogeneously. The mixed hybridcomposite powders were produced in a metal mold using a powder metallurgy hot pressing method at 250 MPa load and 575C temperature for 60 minutes. The microstructural properties of the test samples were investigatedIn addition, density, microhardness and wear test results were examined in terms of mechanical properties. The hybrid sample with 8h mechanical alloying obtained the highest hardness value 118.5 HV and the lowest friction coefficient 0.1965 µm.

Makale detayları

Investigation of the Effect of Mechanical Alloying on the Wear Behavior of AA7020/Fe3O4/GNP Hybrid Composite Materials

Yazarlar:

Ufuk Taşcı

Yayıncı:

Gazi University

Ana Başlıklar:

Powder Metallurgy

Dergi:

Gazi University Journal of Science Part A: Engineering and Innovation Vol.11 Issue 4, pp.814-825

Belge Tipi:

Makale

Yayın Tarihi:

12/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001336828

pISSN:

2147-9542

Mechanical Alloy

Hybrid Composite

Graphene

Fe3O4

Tribology Behavior

Sayı

Makale detayları

Investigation of the Effect of Mechanical Alloying on the Wear Behavior of AA7020/Fe3O4/GNP Hybrid Composite Materials

Yazarlar: Ufuk Taşcı

Yayıncı: Gazi University

Ana Başlıklar: Powder Metallurgy

Dergi: Gazi University Journal of Science Part A: Engineering and Innovation Vol.11 Issue 4, pp.814-825

Belge Tipi: Makale

Yayın Tarihi: 12/2024

Belge Dili: İngilizce

Document ID (Org No.): 2001336828

pISSN: 2147-9542

Mechanical Alloy

Hybrid Composite

Graphene

Fe3O4

Tribology Behavior

Sayı

Yazarlar:

Ufuk Taşcı

Yayıncı:

Gazi University

Ana Başlıklar:

Powder Metallurgy

Dergi:

Gazi University Journal of Science Part A: Engineering and Innovation Vol.11 Issue 4, pp.814-825

Belge Tipi:

Makale

Yayın Tarihi:

12/2024

Belge Dili:

İngilizce

Document ID (Org No.):

2001336828

pISSN:

2147-9542